My tube preamp cable is xlr to TRS, which is why I'm looking for that balanced TRS port. My Mic to tube preamp is already xlr to xlr so I have that cable. I do need balanced audio signals (forgot about that) ,but I need them to be in the form of TRS because of my current cables, or the typical XLR if the dedicated preamp is good enough to remove my tube preamp. Yes I had the USB connected and it still did not work. Thanks for your replies too, the last 2 forums I got literally no responses. I'm sure most mics are easily powered, but just in case mine is 200ohms output Headphone out obviously, with at least 10ohms output TRS in and out, unless preamp is good enough to replace my cheap behringer tube preamp, if so then it needs XLR of couse. But how would I know that it will be able to use SPDIF alone? And what would you suggest? If the solution is to return it and get a different one then I'm perfectly fine doing so. The app also has a pretty well made Auto Echo Cancellation for when I'm using my Mic on discord and such.Īs far as it not having a dedicated DAC and it not being able to use optical alone, I didn't know that. I bought the FCA610 so that I could have everything setup outside, while still being able to utilize the surround sound emulators from my Xonar app. I no longer want to use my sound card as my DAC anymore because I'm trying to eliminate the static feedback from having audio connections inside my pc. It was super cheap and it was pretty much only used to run my tube pre into it. It only had a USB and coax inputs, but I've decided I want to use SPDIF. I originally had my headphones to my sound card because my previous external DAC didn't have enough output impedance for either of my headphones. I am choosing to use the sound card (only $45 btw) specifically for the digital surround sound and not the DAC intentionally. I have cycled through every device in my playback devices with USB connected as well, but still no luck. BEHRINGER FIREPOWER FCA610 POWER DRIVERSI also had the USB plugged in with the drivers installed, and a very barebones app came with it that allowed me to change the sample rate and clock source, everything else was just a list of ports available to connect to with no options other than renaming them. I'm aware of all of the above suggestions, and the connections are all connected properly without a doubt. I'm going to reply to everyone in one post, if that's alright. The FCA610's optical LED indicator also appears solid without flashing, meaning it has connection proper connection. The SPDIF cable does appear to work properly, since the small red light is visible before connecting it to the FCA610. I'm of course trying to drive digital signal (emulated surround sounds) through my headphones (DT 770 80ohm),which are connected to the FCA610's headphone output. The microphone issue is the second part of this, but if anyone could even solve the first one I'd be happy. I'd appreciate a brief rundown as to why this isn't working, as I've seen so many other people drive digital signals from the sound card to their external DAC doing everything I have just mentioned. I have tried using another pair of headphones with 64ohms and it still didn't work. All I have changed is the DAC, and it has 10ohms of output impedance for headphones which is right on target. I mentioned the microphone situation because I'm not getting any signal from the mic either, and I was just using a different DAC yesterday with this setup working perfectly fine. It's a bit of a chain but I enjoy the tube sound as do people hearing me, so I had to choose this specific DAC for all of the right I/O's. It has 2 direct inputs on the front and 4 TRS inputs on the back, and I use 1 backside TRS input to have my tube preamp connected, with the mic into the tube pre. The FCA610's optical LED indicator also appears solid without flashing, meaning it has connection proper connection.Īnother thing to point out, is that I chose this DAC simply because it had the proper I/O's for microphones. I'm of course trying to drive digital signal (emulated surround sounds) through my headphones (DT 770 80ohm), which are connected to the FCA610's headphone output. I have the sound card as the default device in windows, and I have the SPDIF out option checked in the Xonar DGX Audio Center app. I have an SPDIF outputting from the sound card and obviously inputting to the FCA610. I have a Xonar DGX in my computer and a Behringer FCA610 as the external, but I can't seem to get any sound no matter what I try.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |